Buick LeSabre Engine Parts

ENGINE SPLASH SHIELD -- Made of high-density polyethylene for maximum durability and tensile strength; Built to exact OE dimensions for a precise fit; Backed by 1-year, unlimited-mileage warranty.

Fits the following 2000-2005 Buick LeSabre submodels:

• 2000-2005: Custom; 6 Cyl 3.8L;
• 2000-2005: Limited; 6 Cyl 3.8L;

MARSHALL ENGINES PREMIUM LONG BLOCK, REMANUFACTURED

Marshall Engines Remanufactured Premium Long Block Engines are built to the superior quality standards, assembled with precision and impeccable quality control, superior to rebuilt engines, and are shipped with the best warranty in the replacement engine industry. Completely remanufactured engine with all new wear parts, tight tolerances, and run-tested reliability.

Specifications:

• OHV
• Rear wheel drive
• Flat tappet
• 14-bolt oil pan

Features:

• 100 percent mag inspected and pressure tested, vacuum tested for perfect seal, decks milled and surface checked
• Supplied with adjusted valve train components, gasket set, new oil pump, and emissions equipment
• Bake cleaned and shot blasted cylinder heads
• Checked bend and journal polished to achieves perfect seal
• Installed camshafts, valves and springs, and 3-angled cut on valve seats
• Micro-polished design exceeding the original finish ensuring proper bearing lubrication and a final wash to ensure that crank is clean

Not supplied with valley pan gasket.

Fits the following 1979-1984 Buick LeSabre submodels:

• 1982-1984: Custom; 6 Cyl 3.8L; "GAS, CARB, Naturally Aspirated, VIN A"
• 1979-1984: Limited; 6 Cyl 3.8L; "GAS, CARB, Naturally Aspirated, VIN A"

• 1982-1982: Limited Edition F/E; 6 Cyl 3.8L; "GAS, CARB, Naturally Aspirated, VIN A"

• 1981-1981: Sport; 6 Cyl 3.8L; "GAS, CARB, Naturally Aspirated, VIN A"

• 1979-1981: Base; 6 Cyl 3.8L; "GAS, CARB, Naturally Aspirated, VIN A"

Fits 3 more submodels. (Show all) Show less info

A1 CARDONE ENGINE CONTROL COMPUTER, REMANUFACTURED

A1 Cardone Engine Control Computers are designed to render durable and exceptional performance, control emissions, monitor, and regulate engine performance and fuel consumption.

Features:

• 100 percent resolder of critical components
• Superior electrical connections, no intermittent failures, and longer product life
• Corrects OE design flaw and ensures chips will not lift from the board causing the unit to fail
• Defective OE conformal coating is removed from the entire ECM board including underneath chips and replaced with upgraded conformal coating

Fits the following 1980-1981 Buick LeSabre submodels:

• 1981-1981: Base; 6 Cyl 4.1L;
• 1981-1981: Limited; 6 Cyl 4.1L;

• 1981-1981: Sport; 6 Cyl 4.1L;

• 1980-1981: Base; 6 Cyl 3.8L;

• 1980-1981: Limited; 6 Cyl 3.8L;

• 1980-1981: Sport; 6 Cyl 3.8L;

Fits 4 more submodels. (Show all) Show less info

FELPRO ENGINE GASKET SET -- Contains head gaskets, intake gaskets, exhaust gaskets, valve cover gaskets, oil pan gaskets, valve stem seals and all accessory gaskets; Everything you need for a complete engine rebuild; Set contents may vary depending on application; With 1-year Felpro limited warranty.

Fits the following 1977-1979 Buick LeSabre submodels:

• 1979-1979: Limited; 8 Cyl 5.7L; "VIN L"
• 1977-1979: Base; 8 Cyl 5.7L; "VIN L"

• 1977-1978: Custom; 8 Cyl 5.7L; "VIN L"

• 1977-1977: Custom Sport; 8 Cyl 5.7L; "VIN L"

Fits 2 more submodels. (Show all) Show less info

MR GASKET ENGINE REBUILDER ENGINE OVERHAUL GASKET SET -- Full gasket set type; Includes gaskets for the cylinder head, intake and exhaust manifolds, timing cover, fuel pump, crankshaft, oil pump and valve covers, and seals; Designed to rebuild stock engines; Engineered to meet or exceed OE gasket and seal specifications; With Mr. Gasket's limited 90-day warranty.

Fits the following 1970-1976 Buick LeSabre submodels:

• 1970-1976: Custom; 8 Cyl 7.5L;
• 1975-1975: Base; 8 Cyl 7.5L; "GAS, CARB, Naturally Aspirated"

• 1975-1975: Custom; 8 Cyl 7.5L; "GAS, CARB, Naturally Aspirated"

• 1974-1974: Base; 8 Cyl 7.5L; "VIN P"

• 1974-1974: Base; 8 Cyl 7.5L; "VIN R"

• 1974-1974: Base; 8 Cyl 7.5L; "VIN W"

• 1974-1974: Luxus; 8 Cyl 7.5L; "VIN P"

• 1974-1974: Luxus; 8 Cyl 7.5L; "VIN R"

• 1974-1974: Luxus; 8 Cyl 7.5L; "VIN T"

• 1974-1974: Luxus; 8 Cyl 7.5L; "VIN U"

• 1974-1974: Luxus; 8 Cyl 7.5L; "VIN W"

• 1972-1974: Base; 8 Cyl 7.5L; "VIN T"

• 1971-1974: Base; 8 Cyl 7.5L; "VIN U"

• 1972-1973: Custom; 8 Cyl 7.5L; "VIN T"

• 1971-1971: Custom; 8 Cyl 7.5L; "VIN U"

• 1970-1970: Base; 8 Cyl 7.5L;

Fits 14 more submodels. (Show all) Show less info

AC DELCO ENGINE CONTROL MODULE, REMANUFACTURED -- A high quality, OE replacement engine control module; With 12-month or 12,000-mile AC Delco warranty.

Fits the following 1987-1988 Buick LeSabre submodels:

• 1987-1988: Base; 6 Cyl 3.8L; "GAS, FI, Naturally Aspirated, VIN 3"
• 1987-1988: Custom; 6 Cyl 3.8L; "GAS, FI, Naturally Aspirated, VIN 3"

• 1987-1988: Limited; 6 Cyl 3.8L; "GAS, FI, Naturally Aspirated, VIN 3"

• 1987-1987: T-Type; 6 Cyl 3.8L; "GAS, FI, Naturally Aspirated, VIN 3"

Fits 2 more submodels. (Show all) Show less info

SPECTRE ENGINE DRESS-UP KIT, CHROME -- Includes one pair of tall baffled valve covers and valve cover gaskets, eight spreader bars and T-bar hold downs, one breather, one dipstick and tube, two grommets, timing cover kit, and timing tab.

Fits the following 1978-1978 Buick LeSabre submodels:

• 1978-1978: Base; 8 Cyl 5.0L;
• 1978-1978: Custom; 8 Cyl 5.0L;

WESTAR TORQUE STRUT MOUNT, SOLD INDIVIDUALLY -- This is a high quality, direct fit OE replacement torque strut mount.

Fits the following 1992-1999 Buick LeSabre submodels:

• 1992-1999: Custom; 6 Cyl 3.8L;
• 1992-1999: Limited; 6 Cyl 3.8L;

STANDARD ENGINE CONTROL COMPUTER

A high quality, OE replacement engine control computer.

Specifications:

• 4 + 4 terminals
• Non-flashable
• Female connector
• 2 electrical connectors
• Male terminal

Fits the following 1980-1981 Buick LeSabre submodels:

• 1981-1981: Base; 6 Cyl 3.8L; "VIN A"
• 1981-1981: Base; 8 Cyl 5.0L; "VIN Y"

• 1981-1981: Limited; 6 Cyl 3.8L; "VIN A"

• 1981-1981: Limited; 8 Cyl 5.0L; "VIN Y"

• 1981-1981: Sport; 6 Cyl 3.8L; "VIN A"

• 1981-1981: Sport; 8 Cyl 5.0L;

• 1980-1980: Base; 8 Cyl 4.9L; "VIN W"

• 1980-1980: Limited; 8 Cyl 4.9L; "VIN W"

Fits 6 more submodels. (Show all) Show less info

EDELBROCK POWER PACKAGE TOP END KITS -- Includes Performer RPM hydraulic cams and lifters, 2 performer RPM heads, Timing cover and seal set, cylinder head gasket and seal set, RPM Air-gap intake manifold, intake manifold kit, and cylinder head bolt set; With Edelbrock's limited 1-year warranty.

Fits the following 1978-1978 Buick LeSabre submodels:

• 1978-1978: Base; 8 Cyl 5.0L;
• 1978-1978: Custom; 8 Cyl 5.0L;

VICTOR REINZ ENGINE GASKET SET -- Cylinder head type; Provides optimum seal; Handles drastic temperature extremes, high internal pressures, coolants, and lubricants with unsurpassed standards of innovation and quality.

Fits the following 1978-1978 Buick LeSabre submodels:

• 1978-1978: Base; 8 Cyl 5.7L;
• 1978-1978: Custom; 8 Cyl 5.7L;

DEA ENGINE TORQUE STRUT MOUNT -- Helps reduce wheel hop and traction loss; Prevents damage to other vehicle components; Resistant to oils, coolants, and road contaminants.

Fits the following 1992-1999 Buick LeSabre submodels:

• 1992-1999: Custom; 6 Cyl 3.8L;
• 1992-1999: Limited; 6 Cyl 3.8L;

Delphi
Delphi is an Original Equipment supplier to over 25 vehicle manufacturers and is the largest and most diversified supplier of automotive parts to the global aftermarket.

Fits the following 1994-1995 Buick LeSabre submodels:

• 1994-1995: Custom; All Engines;
• 1994-1995: Limited; All Engines;

BLUE PRINT ENGINE ASSEMBLY, DRESSED, NEW

Blue Print Engine Assembly is completely balanced, blueprinted, and dyno-tested. Comes complete with a fuel system, ignition system, and water and fuel pumps. Tested, analyzed, and ensures predictable and reliable performance.

Specifications:

• 1.44 in. diameter valve springs
• 2.02 in. swirl polished intake valves
• 1.6 in. swirl polished exhaust valves
• 380 ft./lbs. of torque
• 9.5:1 compression ratio
• Dyno tested to produce 360 h.p.
• 4 bolt main block
• Square and parallel decked
• Align honed main bearing bore
• Hardened push rods, retainers, and springs
• Flat tappet hydraulic lifter
• New Dart aluminum cylinder heads
• Includes Professional Products dual plane satin finish intake manifold, Edelbrock 600 cfm carburetor, Signature series aluminum valve covers, and brass freeze plugs

Features:

• 110 degree lobe separation
• Duration at 0.05 in. lift is 224 intake/230 exhaust and maximum lift of 0.48 in. intake/0.49 in. exhaust
• Ignition timing: 13 to 16 degree initial/34 degree total timing advance
• Balanced within 2g on a computerized balancer
• Cylinders are sonic tested for thickness and honed on a computer controlled machine to within 0.0002 in. straightness and roundness
• New Scat cast crankshaft, new Scat I-beam rods, Keith Black hypereutectic pistons with Hastings moly rings, Melling high volume oil pump, and heavy duty double roller timing set

Driver side dipstick sold separately.

Fits the following 1968-1985 Buick LeSabre submodels:

• 1985-1985: Collector's Edition; 8 Cyl 5.7L; "GAS, CARB, Naturally Aspirated"
• 1985-1985: Estate Wagon; 8 Cyl 5.7L; "GAS, CARB, Naturally Aspirated"

• 1979-1985: Limited; 8 Cyl 5.7L; "GAS, CARB, Naturally Aspirated"

• 1968-1985: Custom; 8 Cyl 5.7L; "GAS, CARB, Naturally Aspirated"

• 1982-1982: Limited Edition F/E; 8 Cyl 5.7L; "GAS, CARB, Naturally Aspirated"

• 1981-1981: Sport; 8 Cyl 5.7L; "GAS, CARB, Naturally Aspirated"

• 1968-1981: Base; 8 Cyl 5.7L; "GAS, CARB, Naturally Aspirated"

• 1977-1977: Custom Sport; 8 Cyl 5.7L; "GAS, CARB, Naturally Aspirated"

• 1974-1974: Luxus; 8 Cyl 5.7L; "GAS, CARB, Naturally Aspirated"

Fits 7 more submodels. (Show all) Show less info

TRANSDAPT ENGINE DRESS UP KIT -- Includes two tall valve covers, push-in breather, grommets, timing chain cover, timing tab, dipstick, and tube.

Fits the following 1978-1978 Buick LeSabre submodels:

• 1978-1978: Base; 8 Cyl 5.0L;
• 1978-1978: Custom; 8 Cyl 5.0L;